Alarming Function Electrical Safety Test Equipment 5~32A 10~600mΩ Earth Resistance Tester
|
...Resistance Tester Electrical Safety Test Equipment 5~32A/10~600mΩ 1. Introduction Ground Resistance tester (earth resistance tester) is applied to test the ground resistance between conductive parts and earth terminal. Ground resistance is one of important index of safety performance of various electrical equipment. It measures the resistance of the ground loop at a high current (like 10A, 25A or 70A), and also tests......
Pego Electronics (Yi Chun) Company Limited
|
Electrical Safety Testing System AC Hipot Test With 19" LCD Monitor
|
Electrical Safety Testing System/Machine/Safety Testing Solution 1. Safety testing system introduction This electrical safety testing system supports to test leakage current, AC Hipot, insulation resistance, grounding resistance, no load power and low-voltage start up. Up to 100 sets of testing conditions can be memorized. With 8 testing......
Qingdao AIP Intelligent Instrument Co., Ltd
|
ISO 6469 Electrical Safety Testing Equipment For Electric Commercial Vehicles
|
...Electrical Safety Test System For Electric Commercial Vehicles Complied Standards & Clauses ISO 6469-1:2019 Electrically propelled road vehicles — Safety specifications — Part 1: Rechargeable energy storage system (RESS) GB 38032-2020 Safety Requirements for Electric Buses ... Equipment Overview For the vehicle safety test and high voltage safety test of new energy vehicles (commercial vehicle), we launch SNE6809CS series special safety...
Sinuo Testing Equipment Co. , Limited
|
6000W Electrical Testing Resistivity Meter For Groundwater Exploration
|
... is injected into the ground through two electrodes and voltages on the surface are measured revealing the direction and amount of current flow in the subsurface. The data is used to image the subsurface resistivity. Observed measurements of the...
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
|
NK Series Electrical Safety Test Equipment Push Pull Meter Easy Operate
|
NK series pointer push pull meter Usage Spring and rubber strength determination. Determination of operating force of a switch button: telephone, computer, remote control. Plug and pull out force of connector can be tested at the same time. The new ......
KingPo Technology Development Limited
|
Scratch Resistant Pin Electric Safety Testing Probes IEC60335-1 Clause 21 Electrical Solid Insulation
|
Scratched Pin Electric Safety Testing Probes Product information: The test pin is used to do the scratch resistant test of the electrical solid insulation surface. It conforms to the standard requirement of IEC60335-1 clause 21. Test method: make sure the ......
Guangzhou HongCe Equipment Co., Ltd.
|
IEC60335 Electrical Safety Testing Probe Pin For Scratch Resistance Test
|
...Electrical Safety Testing Probe Pin For Scratch Resistance Test IEC60335-1 Clause 21 Scratched Pin For Scratch Resistance Test Of The Electrical Solid Insulation Surface Product information: The test pin is used to do the scratch resistant test of the electrical solid insulation surface. It conforms to the standard requirement of IEC60335-1 clause 21. Test......
Dongguan Kingpo Technology Limited
|
Safety Compliance Test Bench For Conduct Electrical Safety Tests On Electronic Devices 220V
|
Safety Compliance Test Bench For Conduct Electrical Safety Tests On Electronic Devices Product information: Test purpose: Used to provide stable power supply for measurement of various electricians and electrical products. Equipment structure: It is made of 1.5-thick all-steel cabinet with baking paint. The tabletop can be used to place test......
Sinuo Testing Equipment Co. , Limited
|
Eddy Current Testing Resistivity Meter Equipment With Coil Probe
|
...Resistivity Measuring Instrument TMD-110 APPLICATION ● measurement of electrical conductivity of wires and cables ● measurement of electrical conductivity of bar, pipe and profile metal ● research on metal materials ● material sorting in production workshop FEATURES Ø It is used to measure the resistance, meter resistance, kilometer resistance, DC resistance......
TMTeck Instrument Co., Ltd
|
Scratch Resistant Pin Electrical Safety Test Probe of IEC 60335-1
|
...standard requirement of IEC60335-1 clause 21. Test method: Make sure the angle between the pin and the surface of the sample is 80-85°. Then use the pin which is loaded with the axial force of 10±0.......
HK LEE HING INDUSTRY CO., LIMITED
|
Submit your “electrical safety testing resistance meter” inquiry in a minute :