Introduction of differential diffused silicon pressure sensor:
HT20V is a differential pressure sensoris a differential pressure sensitive device isolated by stainless
steel double corrugated diaphragm. Precise measurements are
achieved by isolating the diaphragm and filling the silicone oil to
the silicon pressure sensitive element. The sensor adopts the
international advanced silicon pressure chip with high stability
and high precision, and adopts the sintered base designed by stress
optimization. The production process of the sensor includes: patch,
gold wire bonding, film welding, high vacuum oil injection,
pressure circulation stress relief, high temperature aging,
temperature compensation, etc. The shape, size and sealing method
of the general products are consistent with the international
mainstream products of the same kind, and the interchangeability is
good. They are widely used for differential pressure and level
measurement in 316L stainless steel compatible media.
Product Features of differential diffused silicon pressure sensor:
- Stable and reliable performance
- High resistance to static pressure
- Cost-effective
Applications of differential diffused silicon pressure sensor:- Differential pressure detectiony
- Pressure calibration instruments
- Liquid level measurement
Electrical performance of differential diffused silicon pressure sensor:- Power Supply: ≤10VDC
- Common Mode Voltage Output: 50% of the input (typical)
- Input Impedance:4KΩ~20KΩ
- Output Impedance:2.5KΩ~6KΩ
- Electrical Connection:100mm high-temperature wire.
| Performance Parameters of differential diffused silicon pressure sensor: |
| Measurement Range | 10KPa,35KPa,100KPa,200KPa,350KPa,1000KPa,2000Kpa |
| Typ | Max | Unit |
| Linearity | ±0.15 | ±0.3 | %F.S |
| Repeatability | 0.05 | 0.1 | %F.S |
| Hysteresis | 0.05 | 0.1 | %F.S |
| Zero Offset Output | 0±1 | 0±2 | mV |
| Full Scale Output | ≤20KPa | 50±1 | 50±2 | mV |
| ≥35kPa | 100±1 | 100±2 | mV |
| Zero Offset Temp. Drift | ≤20KPa | ±1 | ±2.5 | %F.S |
| ≥35kPa | ±0.8 | ±1.5 | %F.S |
| Full Scale Temp. Drift | ≤20KPa | ±1 | ±2 | %F.S |
| ≥35kPa | ±0.8 | ±1.5 | %F.S |
| Compensated Temp. | ≤20KPa | 0~50 | ºC |
| ≥35kPa | 0~70 | ºC |
| Operating Temperature | -20~80 | ºC |
| Storage Temperature | -40~125 | ºC |
| Allowable Overload | Take the smaller value between 3 times the full scale or 4MPa | |
| Burst Pressure | 5X the full scale | |
| Long-term Stability | 0.2 % | F.S/Year |
| Diaphragm Material | 316L | |
| Insulation Resistance | ≥200MΩ 100VDC | |
| Vibration | No change under conditions of 10gRMS, 20Hz to 2000Hz | |
| Shock | 100g,11ms | |
| Response Time | ≤1ms | |
| O-ring Seal | Nitrile rubber or Fluoro rubber | |
| Filling Medium | Silicon Oil | |
| Weight | ~45g | |
| The parameters are tested under the following conditions: Constant
voltage of 10V and ambient temperature of 25ºC |
| Outline Construction of differential diffused silicon pressure sensor |
| Dimension |  |
| Notes:The outgoing end is the positive terminal. If there are any
changes in the wire colors, please refer to the label attached to
the sensor for accurate information |
| Electrical connection and compensation of differential diffused silicon pressure sensor |
|
1. Pay attention to the fit between the core size and the
transmitter housing during assembly to achieve the
required airtightness
2. During the assembly of the housing, ensure it is aligned
vertically and apply even pressure to avoid jamming or damaging the
compensation plate.
3. If the measured medium is not compatible with the core diaphragm
and the housing material (316L), special instructions should be
provided when placing the order.
4. Avoid pressing the sensor diaphragm with hands or sharp objects
to prevent damage to the core due to diaphragm deformation or
piercing.
5. Keep the pressure port of the gauge pressure core open to the
atmosphere and prevent the entry of water, water vapor, or
corrosive media into the core negative pressure chamber.
6. If there are any changes to the pin leads, follow the label on
the actual core for reference.
1.Q: What are the features of your pressure sensor transmitters?
A: High precision, durability, and excellent performance.
Customization available.2.Q: Can I customize special specifications?
A: Yes, our engineers can tailor products to meet specific needs. We provide OEM and ODM service3.Q: What is your production capacity?
A: Our manufacturing facilities can produce up to 30,000 pressure
sensor transmitters per month, so we are fully capable of meeting
the needs of large-scale orders. However, it is advisable to
contact our sales team in advance to ensure smooth production and
delivery scheduling
.4.Q: What's the typical delivery period?
A: 5~8 working day for standard models. Customized products may
vary.5.Q: How are the products priced? Any discounts?
A: Competitive pricing with discounts for bulk orders or long-term
partners
.6.Q: What is the warranty of your products? And after-sales
service?
A: Our warranty time is 24 months after shipment, and our
after-sales will respond with your questions in 24hrs, remote
instruction by PC network is always available.
HT24 Flush Silicon Pressure Sensor Hygienic Environmental Liquid Pressure Sensor
