4H Semi-Insulating SiC Production Grade With High Resistivity,4”Size

PAM-XIAMEN offers semiconductor silicon carbide wafers,6H SiC and 4H SiC in different quality grades for researcher and industry manufacturers. We has developed SiC crystal growth technology and SiC crystal wafer processing technology,established a production line to manufacturer SiCsubstrate,Which is applied in GaNepitaxydevice,powerdevices,high-temperature device and optoelectronic Devices. As a professional company invested by the leading manufacturers from the fields of advanced and high-tech material research and state institutes and China’s Semiconductor Lab,weare devoted to continuously improve the quality of currently substrates and develop large size substrates.

Here shows detail specification

SILICON CARBIDE MATERIAL PROPERTIES

4H Semi-Insulating SiC Production Grade,4”Size

SiC crystal application

Many researchers know the general SiCapplication:III-V Nitride Deposition;OptoelectronicDevices;High Power Devices;High Temperature Devices;High Frequency Power Devices.But few people knows detail applications, We list some detail application and make some explanations.

Detail Application of Silicon Carbide

Because of SiC physical and electronic properties,silicon carbide based device are well suitable for short wavelength optoelectronic, high temperature, radiation resistant, and high-power/high-frequency electronic devices,compared with Si and GaAs based device.

Many researchers know the general SiC application:III-V Nitride Deposition;Optoelectronic Devices;High Power Devices;High Temperature Devices;High Frequency Power Devices.But few people knows detail applications, here we list some detail application and make some explanations:

1. SiC substrate for X-ray monochromators:such as,using SiC's large d-spacing of about 15 A;

2. SiC substrate for high voltage devices;

3. SiC substrate for diamond film growth by microwave plasma-enhanced chemical vapor deposition;

4. For silicon carbide p-n diode;

5. SiC substrate for optical window: such as for very short (< 100 fs) and intense (> 100 GW/cm2) laser pulses with a wavelength of 1300 nm. It should have a low absorption coefficient and a low two photon absorption coefficient for 1300 nm.

6. SiC substrate for heat spreader: For example,the Silicon carbide crystal will be capillary bonded on a flat gain chip surface of VECSEL (Laser) to remove the generated pump heat. Therefore, the following properties are important:
1) Semi-insulating type required to prevent free carrier absorption of the laser light;

2) Double side polished are preferred;

3) Surface roughness: < 2nm, so that the surface is enough flat for bonding;

7. SiC substrate for THz system application: Normally it require THz transparency

8. SiC substrate for epitaxial graphene on SiC:Graphene epitaxy on off axis substrate and on axis are both available, surface side on C-face or Si face are both available.

9. SiC substrate for process development loke ginding, dicing and etc

10. SiC substrate for fast photo-electric switch

11. SiC substrate for heat sink: thermal conductivity and thermal expansion are concerned.

12. SiC substrate for laser: optical, surface and stranparence are concerned.

13. SiC substrate for III-V epitaxy, normally off axis substrate are required.

Xiamen Powerway Advanced Material Co.,Limited is an expert in SiC substrate, he can give researchers suggestions in different application

SiC Electronic Devices and Circuits

This section briefly summarizes a variety of SiC electronic device designs broken down by major application areas. SiC process and material technology issues limiting the capabilities of various SiC device topologies are highlighted as key issues to be addressed in further SiC technology maturation. Throughout this section, it should become apparent to the reader that the most difficult general challenge preventing SiC electronics from fully attaining beneficial capabilities is attaining long-term high operational reliability, while operating in previously unattained temperature and power density regimes. Because many device reliability limitations can be traced to fundamental material and junction/interface issues already mentioned in Sections 5.4 and 5.5, efforts to enable useful (i.e., reliable) SiC electronics should focus on improvements to these fundamental areas.

Xiamen Powerway Advanced Material Co.,Limited(PAM-XIAMEN) is a high-tech enterprise for compound semiconductor material integrating semiconductor crystal growth, process development and epitaxy, specializing in the research and production of compound semiconductor wafers, there are two main field: SiC&GaN material(SiC wafer and epitaxy, GaN wafer and epi wafer) and III-V material (III-V substrate and epi service: InP wafer, GaSb wafer, GaAs wafer, InAs wafer and InSb wafer). Our wafers are widely used in LED semiconductor lighting,wireless communication, solar power, infrared device, laser, detectors and semiconductor power devices, including power devices, high temperature devices and photoelectric devices, therein, GaN wafer including GaN on Si,GaN on SiC and GaN on Sapphire are for Mini / micro LED, power electronics and microwave RF.

As a leading professional company, we are committed to constantly improving the quality of existing products. PAM-XIAMEN has a strong technical R & D team, composed of graduate students, doctors, masters, and has a strong R & D strength. The technical backbone of the company has been engaged in material preparation and related equipment design and development for almost 30years, and has in-depth research on the physical, chemical and electrical properties of materials, material preparation process. The accumulation of many years of theoretical deposition and practical experience of scientific and technological personnel makes the company have unique insights and unique advantages in the development of relevant materials and equipment, while ensuring that the product performance and equipment design scheme of the company meet the actual technical and technological needs of users.